User manual ACER ICONIA W511

[. . . ] Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective companies. ii , 03257$17 6$)(7< , 16758&7, 216 1. Save these instructions for Follow all warnings and instructions marked on the product. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. [. . . ] Unscrew the screw knobs and carefully pull out the power supply until it detaches from the housing. Make sure the power supply subsystem is supplying a minimum of 860W (2 power supply modules) to the system. 2-28 AcerAltos 21000 System Guide 2. 6 Installing and Removing a Hot-swappable Redundant Housing Fan Four housing fans are distributed inside the housing to cool down the system. You can simply take one out and put a new one in if a fan fails to operate. Turn the screw knob counterclockwise to open the housing fan cage. System Housing 2-29 2. Close the housing fan cage and turn the screw knob clockwise to lock it. 2-30 AcerAltos 21000 System Guide To change a front hot-swap housing fan: 1. Close the left panel. System Housing 2-31 2. 7 Installing an Expansion Board Follow these steps to install a PCI expansion board: 1. Secure the board with a screw. 2-32 AcerAltos 21000 System Guide 5. Follow the same steps when installing an ISA board. Just make sure that you remove the bracket cover opposite an ISA slot. System Housing 2-33 2. 8 Removing and Installing the Thermal Air Guide On the left side of the housing, a metal thermal air guide directs the hot air from the inside to the fan exhausts on the rear of the housing. The air guide helps in maintaining good air circulation within the housing. To avoid electric shock and damage to the system, DO NOT perform the following procedure while the system is ON. 2. 8. 1 Removing the Thermal Air Guide Follow these steps to remove the thermal air guide: 1. Save the screws. 4. Carefully remove the air guide from the housing and set it aside. 2-34 AcerAltos 21000 System Guide 2. 8. 2 Reinstalling the Thermal Air Guide Follow these steps to replace the thermal air guide back into the housing: 1. Position the air guide in its place as shown below. 2. Make sure that the air guide fits properly in place. System Housing 2-35 3. Reattached the left panel door. 2-36 AcerAltos 21000 System Guide 2. 9 Cable Connections The power backplane is complete with connectors to accommodate the power cables for all the system components. Use the retention mechanism cover to secure the processor as shown below. The retention mechanism cover only fits one way. Both shafts of the retention mechanism and the retention mechanism cover have a O and a OO sign. Match the O on the cover with the O on the retention mechanism first, then hooked them together and then insert the OO side to the retention mechanism and make sure they are clipped. System Boards 3-9 7. Refer to section 3. 1. 2 for the location of the thermal and fan connectors. Refer to the VRM LED guide (section 3. 1. 5) for installing VRMs. A VRM LED with green light indicates that a VRM has to be installed in its socket. 3. 1. 4 Installing and Removing the Termination Board When you are not using all the Slot 2 sockets, you must install a termination board into each empty slot. Installing a Termination Board Follow these steps to install the termination board: 1. Carefully insert the golden fingers of the termination board into the slot until the board fits completely. OO 3. Use the retention mechanism cover to secure the processor by pressing it down until it locks. 3-10 AcerAltos 21000 System Guide The retention mechanism cover only fits one way. Both shafts of the retention mechanism and the retention mechanism cover have a O and a OO sign. Match the O on the cover with the O on the retention mechanism first, then hooked them together and then insert the OO side to the retention mechanism and make sure they are clipped. Removing an Intel Pentium II Xeon processor Follow these steps to remove a Pentium II Xeon processor: 1. [. . . ] [xx:xx:xx] = Move Highlight Bar, = Change Setting, F1 = Help 4-48 AcerAltos 21000 System Guide 4. 9. 1 Date or to set Highlight the items in the Date parameter and press the date following the weekday-month-day-year format. Valid values for weekday, month, day, and year are: · · · · Weekday Month Day Year Sun, Mon, Tue, Wed, Thu, Fri, Sat Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov, Dec 1 to 31 1980 to 2079 4. 9. 2 Time or to set Highlight the items in the Time parameter and press the time following the hour-minute-second format. Valid values for hour, minute, and second are: · · · Hour Minute Second 00 to 23 00 to 59 00 to 59 BIOS Utility 4-49 4. 10 Remote Diagnostic Configuration The Remote Diagnostic Configuration parameter allows you to configure your RDM settings. Refer to the RDM User's Guide for more information on RDM. 4-50 AcerAltos 21000 System Guide 4. 11 Load Setup Default Settings Use this option to load the default settings for the optimized system configuration. [. . . ]