User manual ACER H5360

[. . . ] Monitor Information Product 7763P/65PE Name: Serial Number: Date of Purchase: Dealer Information Dealer: Telephone Number: Address: Caution TO PREVENT SHOCK, DO NOT OPEN THE CABINET. AND PLEASE READ ALL OF THESE INSTRUCTIONS BEFORE YOU OPERATE YOUR PROJECTOR. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE . Safety Instructions 1. Read all of these instructions before you operate your projector and save for future reference. [. . . ] (Move the picture with the Disk Pad after pressing the Magnify button. ) When the OSD menu is active, Disk Pad acts as 56selecting device. When the magnify function is active, use disk pad to move through the picture. And the blank screen will be revealed partially from top to bottom by pressing Blank again. The sound gets louder or quieter by pressing the "+" or "-" button. Use as a stick (for Disk Pad Menu Blank Source Mute Volume Laser Mouse Click Mouse Click Exit 34Drag Left- When operating in mouse emulation mode, it registers a left mouse click. (bottom button) Right- When operating in mouse emulation mode, it registers a right mouse click. To move Left/Right among OSD items. Inserting Batteries in the Remote Control English 11 Be sure to follow instructions in placing batteries into the remote control units. · Install two 'AAA' batteries as indicated inside the battery compartment. · Replace the lid and snap into place. Caution · · Avoid excessive heat and humidity. Do not mix new and old or different types of batteries. Figure 14 Battery replacement process Remote Control Range The remote sensors are located on the back of the unit. It can function in a range 50 degrees horizontal and 30 degrees vertical relative to a line that is a right angle to the remote sensor. On the other hand, when the input source are video, S-video, TV or CATV, there will be other 4 items on this page: Keystone, Brightness, Contrast, and Sharpness(Fig. 22). Press the "Menu" button again to scroll through the items; press "3" or "4" to adjust the item scale, or press the "Exit" button to go back to the main OSD page. Fig. 21 Display sub-page when the input source is PC(with/without AV box) Figure 22 Display sub-page when the input source is video, s-video , TV or CATV Keystone Brightne ss Contrast Color Balance (Decrea se) (Dark) (Lower) (Red) Setting effects (Increas e) (Bright) (Higher) (Blue) Source is PC English 18 Sharpnes s (Soft) (Sharp) Source is Video B Image Page Select the Image sub-page and the first item, "Auto Resize" will be highlighted. If AV box is attached and the input is from Video other instead of PC, another different IMAGE sub-page including Image Ratio, System , Color and Tint will come out as figure 24. Figure 23 Image sub-page. . . . Only available when the input signal is PC Figure 24 Image sub-page ­ Only available when the input signal is from video, S-video, TV or CATV Auto Resize H. Size Setting effects When Auto Resize is on, the projector determines the best fit of the image to the screen. If flicker occurs on a projected image, users may try to adjust the H. If the projected image is too wide or too narrow for the screen, users may turn Auto Image off and adjust the H. Size manually to fit the screen size. English 19 H. Posit ion (move the (move the image right) image left) The Auto Image should be turned off to activate the H. Positio n (move the image down) (move the image up) Position adjustments are saved when the projector is power off. Image Ratio 4:3 (Normal) 16:9 (Wide) To select the input video system standard. When an AV System box or turner box is attached, the projector will automatically detect the video system. When selecting system, the projector will detect the selected system simultaneously, and the OSD will still exit on the screen. [. . . ] A " ¡ü " mark appears at the lower right of the screen for 3 seconds during the freeze function. Furthermore, a "4" mark appears at the lower right of the screen for 3 seconds when freeze is released. "Freeze" is released when the source button or the "Freeze" button is pressed again. There will be an OSD message as shown below: Press Mute again or the volume +/- buttons to turn off the mute. [. . . ]