User manual ACER EXTENSA 5235

[. . . ] Extensa Series Generic User Guide Original Issue: 08/2008 This company makes no representations or warranties, either express or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose. Although care has been taken to ensure accuracy, this company shall not be liable for any errors (including, but not limited to, typos, factual errors, etc. ) contained in this publication. Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. [. . . ] If pressing a key does not turn the display back on, three things might be the cause: The brightness level might be too low. Press <Fn> + < > (increase) to adjust the brightness level. Press the display toggle hotkey <Fn> + <F5> to toggle the display back to the computer. Press and release the power button to resume. No audio is heard from the computer. Check the following: The volume may be muted. If it is crossed-out, click on the icon and deselect the Mute all option. See "Special keys (only for certain models)" on page 5 for 9 more detail. If headphones, earphones or external speakers are connected to the lineout port on the computer, the internal speakers automatically turn off. English I want to eject the optical drive tray without turning on the power. There is a mechanical eject hole on the optical drive. Simply insert the tip of a pen or paperclip into the hole and push to eject the tray. The keyboard does not respond. Try attaching an external keyboard to a USB port on the computer. If it works, contact your dealer or an authorized service center as the internal keyboard cable may be loose. The printer does not work. Check the following: Make sure that the printer is connected to a power outlet and that it is turned on. Make sure that the printer cable is connected securely to the computer's parallel port or a USB port and the corresponding port on the printer. I want to set up my location to use the internal modem. To properly use your communication software, you need to set up your location: 1 2 3 Click on Start, Control Panel. Begin setting up your location. Refer to the Windows manual. Note: Please note, on first booting your notebook, that you can skip the Internet Connection setup, as it is not necessary to complete the installation of your Operating System. After the Operating System is set up, you can proceed with the Internet Connection setup. 10 English I want to restore my computer to its original settings without recovery CDs. Note: If your system is the multilingual version, the operating system and language you choose when you first turn on the system will be the only option for future recovery operations. This recovery process helps you restore the C: drive with the original software content that is installed when you purchase your notebook. (Your C: drive will be reformatted and all data will be erased. ) It is important to back up all data files before using this option. Before performing a restore operation, please check the BIOS settings. The system will reboot. Note: To activate the BIOS utility, press <F2> during POST. While the Acer logo is showing, press <Alt> + <F10> at the same time to enter the recovery process. Refer to the onscreen instructions to perform system recovery. Important!This feature occupies 15 GB in a hidden partition on your hard disk. 11 English Requesting service International Travelers Warranty (ITW) Your computer is backed by an International Travelers Warranty (ITW) that gives you security and peace of mind when traveling. Our worldwide network of service centers are there to give you a helping hand. A list of available, authorized service centers is in this handy booklet. Always have your ITW passport on hand, especially when you travel, to receive the benefits from our support centers. [. . . ] The associated equipment shall be set to operate within the following limits for compliance with Telecom's Specifications: a b There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next call attempt. 2 3 4 Some parameters required for compliance with Telecom's Telepermit requirements are dependent on the equipment (PC) associated with this device. In order to operate within the limits for compliance with Telecom's specifications, the associated equipment shall be set to ensure that automatic calls to different numbers are spaced such that there is not less than 5 seconds between the end of one call attempt and the beginning of another. This equipment shall not be set up to make automatic calls to Telecom's 111 Emergency Service. This device is equipped with pulse dialing while the Telecom standard is DTMF tone dialing. [. . . ]