User manual ACER ASPIRE 5830TG

[. . . ] Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Acer is a registered trademark of Acer Corporation. Pentium Dual-Core, Celeron Dual-Core, Core 2 Duo, Core 2 Quad, Celeron, and combinations thereof, are trademarks of Intel Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders. iv Conventions The following conventions are used in this manual: SCREEN MESSAGES NOTE WARNING CAUTION IMPORTANT Denotes actual messages that appear on screen. Alerts you to any physical risk or system damage that might result from doing or not doing specific actions. [. . . ] This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. The IDE/ATAPI device configured as Slave in the 3rd IDE controller could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. The IDE/ATAPI device configured as Master in the 4th IDE controller could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. The IDE/ATAPI device configured as Slave in the 4th IDE controller could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. The IDE/ATAPI device configured as Master in the 5th IDE controller could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. 49 Chapter 4 Message Displayed Description 5th Slave Hard Disk Error 6th Master Hard Disk Error 6th Slave Hard Disk Error Primary Master Drive ATAPI Incompatible Primary Slave Drive - ATAPI Incompatible Secondary Master Drive ATAPI Incompatible Secondary Slave Drive ATAPI Incompatible 3rd Master Drive - ATAPI Incompatible 3rd Slave Drive - ATAPI Incompatible 4th Master Drive - ATAPI Incompatible 4th Slave Drive - ATAPI Incompatible 5th Master Drive - ATAPI Incompatible 5th Slave Drive - ATAPI Incompatible 6th Master Drive - ATAPI Incompatible The IDE/ATAPI device configured as Slave in the 5th IDE controller could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. The IDE/ATAPI device configured as Master in the 6th IDE controller could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. The IDE/ATAPI device configured as Master in the 6th IDE controller failed an ATAPI compatibility test. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. Chapter 4 50 Message Displayed Description 6th Slave Drive - ATAPI Incompatible S. M. A. R. T. Capable but Command Failed The IDE/ATAPI device configured as Slave in the 6th IDE controller failed an ATAPI compatibility test. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. failure messages may indicate the need to replace the hard disk. S. M. A. R. T. capable hard disk sends this message when it detects an imminent failure. failure messages may indicate the need to replace the hard disk. S. M. A. R. T. capable hard disk sends this message when it detects an imminent failure. failure messages may indicate the need to replace the hard disk. Virus Related Message Displayed BootSector Write VIRUS: Continue (Y/ N)?Description The BIOS has detected software attempting to write to a drive??s boot sector. [. . . ] Step 4:Click on the by`Create RAID Volume from Existing HDD Drive ' to create a RAID volume. Step 6:Key the name in "Volume Name" and select "RAID 10" in RAID Level. Picture14 91 Chapter 7 Step 7:Select two HDDs as "Source Hard Drive". Picture15 Step 8:At least select two HDD as Menber Hard Drive(s). Step 10:Press "next" to finish setup and start create RAID 10. Step 11:It may takes half and hours to create RAID 10. After create completely, it will ask to reboot to finish create RAID10. 2-5:Create a"RAID Ready" System into" RAID 0" with two Hard Drives by `Create RAID Volume '. Step 1:Install WIN7 OS with one SATA HDD. [. . . ]