User manual ACER AL2671W

[. . . ] The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register, or in a builtin installation unless proper ventilation is provided. If the product does not operate normally when the operating instructions are followed. [. . . ] Press repeatedly to switch image between Normal Zoom1 (1. 85:1) Zoom 2 (2. 35:1) English SRS Press to select WOW, TruBass, 3D Stereo, "Off" modes sequentially. SRS is a technology to enhance 3D sound, bass performance and to produce a wider sound field. Scaling mode (4:3 / 16:9 / Panorama / Letterbox) Number keys from 0-9 Press to return to the previous channel. Navigate up, down, left and right in the OSD menu / press OK to confirm. Press to select the sound system, displayed at the top right-hand corner. Press these buttons to select the TV channel in sequence Acer Empowering key (for Favorite Channel, Scenario Mode). See "Empowering Key: Favorite Channels and Scenario Mode" on page 19. Change position of subscreen in PIP mode When in PIP mode: Change subscreen size 25%, 37. 5%, 50% When in POP mode: Change POP mode 1+5 / 1+12 WIDE Number keys RECALL ENTER MENU 4-way scroll key/OK MPX VOL (up/down) CH (up/down) e PIP/PBP/POP SWAP ACTIVE POSITION SIZE/MODE The teletext button descriptions can be found on page 17. 11 Basic connection English Connecting the power cord 1 2 Connect the AC cord into the AC input on the back of the set. Connect the male plug to the wall outlet as shown. Connecting an antenna Connect the outdoor antenna cable lead-in to the antenna terminal on the back of the TV set as shown. 12 Connecting VCR/DVD/AV equipment with a SCART-SCART cable Connect SCART-SCART cable as shown below. English Connecting VCR/DVD/AV equipment with a SCART-component (YPbPr/YCbCr) or composite (AV) cable Connect SCART-component/AV cable to SCART2 port as shown below. For SCART2 only 13 Connecting a camera, camcorder or video game Connect your camera or camcorder to the Video/Audio ports on the bottom of the TV set as shown below. English camera, camcoder, video games Connecting a headphone Connect headphone to the headphone input on the bottom of the TV set as shown below. 14 Getting started watching your TV Power On a. Press the power button on remote control a b Scanning the channels The first time you use your TV, use the following method: Menu -> Settings -> Channel settings -> Scan -> "YES". The TV will auto-detect available channels and store them in memory. English Changing channels 1 Press 0-9 on the remote control to select a channel. Press ENTER to select the channel immediately. The first time you access the OSD, a language setting subwindow will pop up, and you will be asked to choose your language settings. 2 You can also change the channels by pressing and holding the Channel Up/Down button on the remote control. Up will increase the number, while down will decrease the number. Adjusting the volume Adjust the volume using the VOL +/- button on the remote control. Up will increase the volume, while down will decrease the volume. You can also adjust these settings using the front control panel. Please see "Front panel view" on page 8 for details. 15 OSD Navigation English Many of the advanced settings and adjustments are available through using the OSD (on screen display) menus, as shown in the example screenshot below. Basic operations required to navigate these menus (Picture, Audio, Settings, Options, Empowering) are described in this section. The first time you access the OSD, you will be asked to choose your language settings. [. . . ] The `ghost' or double image may be caused by obstruction to the antenna due to high rise buildings or hills. The horizontal dotted lines shown on the pictures may be caused by electrical interference, e. g. Turn off or remove these equipment. Picture is too dark, too light or tinted. · · · · Check the color adjustment. [. . . ]