User manual ACER AL1721

[. . . ] As an ENERGY STAR Partner our company International has determined that this product meets the ENERGY STAR guidelines for energy efficiency. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. 1. 41L1700-786-7A 1 PRECAUTIONS Do not use the monitor near water, e. g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. [. . . ] NOTES A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. 41L1700-786-7A 4 CONTROLS AND CONNECTORS CABLE CONNECTIONS Turn off your computer before performing the procedure below. Connect the power adapter dc cable to the DC-In port on the back of the monitor. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. (only Dual-Input Model)Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. Connect the audio cable between the monitor's audio input and the PC's audio output (green port). External Adapter DVI Cable Audio cable 41L1700-786-7A 5 ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. · Hold the stand so you do not topple the monitor when you change the monitor's angle. · You are able to adjust the monitor's angle from -5° to 15°. Figure 2 NOTES · Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. · Careful attention is required not to catch your fingers or hands when you change the angle. 41L1700-786-7A 6 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. 5. /MENU/ENTER /Auto Adjust Key/Exit /Power Key /LED 41L1700-786-7A 7 FRONT PANEL CONTROL · /Power Button: Press this button to turn the monitor ON or OFF, And display the monitor's state. Blue -- Orange -- Light blue -- Power On mode. Off mode. · Power Indicator: · /MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status. Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. · </Volume: · >/Volume: Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. · 1. 2. /Auto Adjust button / Exit: When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. NOTES · Do not install the monitor in a location near heat sources such as radiators · · · or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean it with a soft cloth. [. . . ] Check the signal -cable connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode , set the computer to display mode given in the following table(See page 18). 41L1700-786-7A 15 APPENDIX SPECIFICATIONS LCD Panel Driving system Size Pixel pitch Brightness Contrast Viewable angle Response time Video H-Frequency V-Frequency Display Colors Dot Clock Max. Resolution Plug & Play EPA ENERGY STAR® ON Mode OFF Mode Input Connector Input Video Signal TFT Color LCD 43. 2cm(17. 0") 0. 264mm( H )x 0. 264mm( V ) 260cd/m2 (Typical) 450:1(Typical) 140° (H) 140° (V) 16 ms(Tr+Tf)Tr=4ms/Tf=12ms R, G, B Analog Interface Digital interface(Dual-Input Model) 30KHz ­ 83KHz 55-75Hz 16. 2M Colors 165MHz 1280 x 1024 @75Hz VESA DDC1/2BTM 45W 3W D-Sub 15pin DVI-D 24pin (Dual-Input Model) Analog:0. 7Vp-p(standard), 75 OHM, Positive Digital signal (Dual-Input Model) Horizontal : 337. 92mm Vertical : 270. 34mm 100~264VAC, 47~63Hz Operating Temp: 5° to 50°C Storage Temp. : -20° to 65°C Operating Humidity: 10% to 85% 377(W)×391(H)×154(D)mm 5. 0kg Unit (net) Maximum Screen Size Power Source Environmental Considerations Dimensions Weight (N. W. ) 41L1700-786-7A 16 Switch External Controls: Functions · · · · · · · · · · · · Power Consumption ( Maximum ) Audio Output Regulatory Compliance Auto Adjust Key </Volume >/ Volume Power Button MENU/ Exit Contrast Brightness Focus Clock H. Position V. Position Input signal Selection (Dual model only) · Language · Auto configuration (Analog model only) · (Warm) Color · (Cool)Color · RGB Color temperature · Reset · OSD position . timeout · Display information · Exit 45 Watts Rated Power 1. 5W rms (Per channel) CUL, FCC, VCCI, CCC, MPR II, CE, TÜV/GS, TCO'99, UL, ISO13406-2 41L1700-786-7A 17 Preset Display Modes STANDARD VGA RESOLUTION 640 × 480 640 × 480 800 × 600 SVGA 800 × 600 VESA XGA 1024 × 768 1024 × 768 1024 × 768 SXGA IBM MAC DOS XGA 1280 × 1024 1280 × 1024 720 × 400 1024 × 768 1024 × 768 46. 875 48. 363 56. 476 60. 023 64. 000 80. 000 31. 469 48. 780 60. 241 75. 000 60. 004 70. 069 75. 029 60. 000 75. 000 70. 087 60. 001 74. 927 HORIZONTAL FREQUENCY(KHz) 31. 469 37. 500 37. 879 VERTICAL FREQUENCY(Hz) 59. 940 75. 000 60. 317 41L1700-786-7A 18 CONNECTOR PIN ASSIGNMENT 1 6 11 5 10 15 15 - Pin Color Display Signal Cable PIN NO. [. . . ]